Product Applications
- About Us
- Products
- Applications
- Services
- Support
- Press Room
- Contact Us
- Contact Info
- Email for Sales
- Email for Support
- Email for Info
- Email for RMAs
- Chinese Website
- Sales Offices
- Distributors
- Job Opportunities
The RFProcess101A is a wireless, battery powered, low level DC Current Data Logger with a built-in wireless (RF) transmitter. This data logger features custom Engineering Units set through the software. Any sensor that provides an analog DC current output signal can be monitored and recorded. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements. The RFProcess101A combines the features from the standard product line and adds the convenience of a wireless transmitter which can transmit data up to 120 feet, line of site. When enabled, the wireless transmitter will transmit readings back to the host computer where the data can be analyzed in real time. These readings are also logged to the device’s memory for added data security. The convenient slide switch allows the transmitter to be turned on or off without effecting the operation of the device. The data logger’s small size allows it to fit almost anywhere.
The RFProcess101A is available with an extended warranty.
Note: Approved for use in the US and Canada only.
The RFProcess101A is available with an extended warranty.
Note: Approved for use in the US and Canada only.
CURRENT
| Current Range | ±1mA ±25mA ±100mA |
|---|---|
| Current Resolution | ±1mA: 0.05μV ±1mA: 0.05μV ±100mA: 5μV |
| Current Calibrate Accuracy | ±1mA: ±5% ±1mA: ±5% ±100mA: ±0.1% |
WIRELESS
| RF Carrier Frequency | 418 ±0.075MHz |
|---|---|
| RF Baud Rate | 4800 |
| Output Power | <0dBm typical (<1mW) |
| Receiver Sensitivity (RFC101A) | -90dBm typical |
| Typical outdoors Line of sight | Up to 120' (36m) |
| Typical Indoors line of sight | Up to 40' (12m) |
GENERAL
| Memory | 8,191 readings |
|---|---|
| Reading Rate | 30 seconds up to 12 hours |
| Baud Rate | 57,600 |
| LED Indicators | Red & Green |
| Battery Life | 1 year |
| Material | ABS plastic |
| Dimensions | 1.7" x 2.7" x 0.8" plus 2.0" antenna (42mm x 69mm x 21mm + 51mm antenna) |
| Operating Environment | -30~+70°C; 0~95%RH non-condensing |
| Required Interface Package | RFC101A or RFC200A |
| Approvals | US(FCC), CA(IC) |
Accessories
Required Accessories
Check items to add to the cart or select all
-
Radio frequency receiver for Standard RF Series Data Loggers. Includes Wireless Receiver, MadgeTech Software CD, Software Manual, Power Supply, IFC200, and Serial to USB Convertor (For RF Receiver).
Knowledge Base
Optional Accessories
-
3.6 Volt, Lithium Battery, 750 mAH
Note: These batteries are only equipped with two leads and the leads have been cut for use with MadgeTech data loggers. For additional configurations, please contact MadgeTech Sales.
Knowledge Base
-
Split core current tranducer, monitors 0-50,100 or 200ADC (slide switch selectable). No status LED's, outputs a 4-20mA and 0-50VDC signal (requires external power).
Knowledge Base
-
Includes software, manual, RS232 (IFC110) computer interface cable and USB to RS232 converter cable.
Knowledge Base
-
Radio Frequency Receiver for Standard RF Series Data Loggers. AC power required, RS232 Connection.
Knowledge Base
-
3.6 Volt, Lithium Battery, 750 mAH (pack of 14)
Note: These batteries are only equipped with two leads and the leads have been cut for use with MadgeTech data loggers. For additional configurations, please contact MadgeTech Sales.
Knowledge Base
-
Split core current switch, monitors 3.5-100Amps, adjustable set point between 3.5-100Amps, auto calibration, status LED's, outputs a 4-20mA signal.
Knowledge Base
-
Click and Drag to Rotate